Guide

Buying a used forklift, the inspection checklist.

The real condition of a used forklift shows in an inspection on site. This guide sets out what to check beside the machine and in what order.

The real condition of a used forklift never shows in the listing photos. Half an hour beside the machine tells you far more. This guide covers what to ask the seller, what to inspect before and after starting the engine and how to test the machine under load.

Ask the seller before you go

A few answers over the phone can save you a wasted trip. Ask the seller for the following.

  • Make, model and year. Ask for the serial number as well. You will compare it with the data plate on the machine.
  • Hours run. Ask for a photo of the hour meter. If the meter has ever been replaced, ask about that separately.
  • Service records. Ask for dated records of oil and filter changes or the workshop invoices.
  • Periodic inspection report. Turkish work equipment safety regulations require forklifts to pass a periodic inspection at least once a year. The date and result of the last report say a lot about how the machine has been used.
  • Known faults. A fault the seller mentions up front makes the negotiation easier.

Ask the seller not to start the machine before you arrive. The first cold start tells you the most.

Checks with the engine off

Inspect the machine on level ground with the forks lowered. This part takes about ten minutes.

  • Serial number plate. The number on the capacity plate should match the one the seller gave you. On a machine with the plate removed, the rated capacity is unknown too.
  • Chassis and mast welds. Factory welds are even and painted. A repair weld added later shows even under fresh paint. If you find one on the mast or the load bearing part of the chassis, ask why it was needed.
  • Fork thickness. Compare the heel of the fork with its vertical shank. Under ISO 5057, a fork is withdrawn from service once heel wear reaches 10 percent of the original thickness.
  • Chains. Both chains should carry equal tension. Rusty, dry looking links mean the chains have gone without lubrication for a long time.
  • Hydraulic hoses and cylinders. Look for cracked hoses, scored cylinder rods or traces of oil. Check the floor where the machine has been standing too.
  • Seat, pedals and steering wheel. These parts show how hard the machine has worked more reliably than the meter. If the hours look low but the pedal rubbers are worn through, do not trust the meter.
  • Tyres. On cushion tyres check the wear line. On pneumatic tyres look for cracks in the sidewalls.

Cold start and exhaust smoke

Watch the sound, the smoke and the dashboard together during the first start. An engine that starts hard or misfires once running is the first warning sign.

Exhaust smokeWhat it suggests
Blue or greyThe engine is burning oil. Piston rings or valve seals may be worn
Black and heavyToo much fuel is burning. The air filter may be blocked or the injectors out of adjustment
White and still there once warmWater or coolant may be entering the combustion chamber. The head gasket needs checking
Brief white vapourNormal in cold weather. It clears once the engine warms up

Once the engine is warm, open the oil filler cap and look underneath. A light brown, frothy layer under the cap means water is getting into the oil.

Testing under load

Most hydraulic and mast faults only appear once there is weight on the forks. If you can, test with a load close to the capacity on the plate.

  • Lifting. Raise the load to full height. The mast should rise without sticking, jerking or noise.
  • Drift test. Lift the load about one metre, switch the engine off and wait ten minutes. If the forks sink noticeably or the mast tilts forward on its own, the cylinder seals are leaking.
  • Tilt. Tilt the mast fully forward and back. The movement should be smooth both ways and the mast should hold the angle where you stop it.
  • Brakes and transmission. Drive forward and in reverse while loaded. There should be no knock on gear changes and no pulling or delay when braking.
  • Steering. Turn fully in both directions with the load on. The steering should not stiffen and the hydraulic pump should not whine.

If the seller will not allow a load test, make a note of it. On a machine bought without one, mast and hydraulic faults only surface once it starts working for you.

Extra checks on an electric forklift

The battery accounts for much of the value of an electric forklift. It is inspected separately from the rest of the machine.

  • Battery label. Read the manufacturing date from the battery’s own label. The battery may not be the same age as the machine.
  • Cell voltages. After a full charge, measure each cell with a voltmeter. There should be no marked difference between cells. A single weak cell shortens the run time of the whole battery.
  • Electrolyte and terminals. Check the electrolyte level under the caps and look for white or green corrosion on the terminals.
  • Charger. Confirm that the charger matches the battery voltage and is included in the sale.
  • Run time. Ask the seller how many hours a fully charged battery lasts. During the test, watch how quickly the charge indicator drops.

Extra checks on an LPG forklift

  • Cylinder mounting. The cylinder cradle and strap should be secure. There should be no smell of gas at the connection.
  • Regulator and hoses. Look for icing or oil on the regulator and cracks in the hoses.
  • Idle. The engine should idle steadily. A hunting idle usually points to an adjustment or regulator problem.

Paperwork, negotiation and after delivery

Ask for an invoice with the sale. The serial number on the invoice should match the plate on the machine.

Every fault you note during the inspection becomes a line in the negotiation. Talk openly with the seller about costs such as tyres, chains, battery and seals. You can ask for either a lower price or repairs before delivery.

If the service history is unclear, change the engine oil, hydraulic oil and filters once the machine is yours. That way the service record starts fresh in your hands.

Frequently asked questions

How many hours is too many on a used forklift?

There is no single limit. A high hour machine that has been serviced regularly can outlast a low hour one that has been neglected. Judge the hours together with the age, the wear marks and the service record.

When should forklift forks be replaced?

Under ISO 5057, a fork is replaced once the heel thickness falls to 90 percent of the original. A fork with a crack or a bend is taken out of service immediately.

Is a load test really necessary before buying?

Testing under load is the most reliable way to find mast and hydraulic faults. Lifting the load one metre, switching off and waiting ten minutes shows whether the forks drift.

Will an electric forklift need a new battery?

That depends on the battery’s age and its cell voltages. A battery that cannot last a shift on a full charge should be priced into the negotiation. A new battery is a large cost compared with the price of the machine.

Can I do these checks myself?

Anyone who has driven a forklift can do most of the visual checks. The drift test and reading the exhaust smoke need no tools either. Measuring the battery cells only takes a voltmeter.

Get a quote

Let's carry your load together.

Tell us your pallet or forklift need and get a quote within minutes.